{
	"activate_air_filtration": [
		"0"
	],
	"activate_air_filtration_during_print": [
		"1"
	],
	"activate_air_filtration_on_completion": [
		"1"
	],
	"activate_chamber_temp_control": [
		"0"
	],
	"adaptive_pressure_advance": [
		"0"
	],
	"adaptive_pressure_advance_bridges": [
		"0"
	],
	"adaptive_pressure_advance_model": [
		"0,0,0\n0,0,0"
	],
	"adaptive_pressure_advance_overhangs": [
		"0"
	],
	"additional_cooling_fan_speed": [
		"0"
	],
	"additional_fan_full_speed_layer": [
		"0"
	],
	"chamber_minimal_temperature": [
		"0"
	],
	"chamber_temperature": [
		"0"
	],
	"close_additional_fan_first_x_layers": [
		"1"
	],
	"close_fan_the_first_x_layers": [
		"1"
	],
	"compatible_printers": [
		"Snapmaker U1 (0.4 nozzle) - 1"
	],
	"compatible_printers_condition": "",
	"compatible_prints": [],
	"compatible_prints_condition": "",
	"complete_print_exhaust_fan_speed": [
		"70"
	],
	"cool_plate_temp": [
		"35"
	],
	"cool_plate_temp_initial_layer": [
		"35"
	],
	"default_filament_colour": [
		""
	],
	"dont_slow_down_outer_wall": [
		"0"
	],
	"during_print_exhaust_fan_speed": [
		"70"
	],
	"enable_overhang_bridge_fan": [
		"1"
	],
	"enable_pressure_advance": [
		"1"
	],
	"eng_plate_temp": [
		"0"
	],
	"eng_plate_temp_initial_layer": [
		"0"
	],
	"fan_cooling_layer_time": [
		"100"
	],
	"fan_max_speed": [
		"100"
	],
	"fan_min_speed": [
		"100"
	],
	"filament_adaptive_volumetric_speed": [
		"0"
	],
	"filament_adhesiveness_category": [
		"0"
	],
	"filament_change_extrusion_role_gcode": [
		""
	],
	"filament_change_length": [
		"10"
	],
	"filament_cooling_before_tower": [
		"10"
	],
	"filament_cooling_final_speed": [
		"3.4"
	],
	"filament_cooling_initial_speed": [
		"2.2"
	],
	"filament_cooling_moves": [
		"4"
	],
	"filament_cost": [
		"22.99"
	],
	"filament_density": [
		"1.25"
	],
	"filament_deretraction_speed": [
		"nil"
	],
	"filament_diameter": [
		"1.75"
	],
	"filament_end_gcode": [
		"; filament end gcode\n"
	],
	"filament_extruder_variant": [
		"Direct Drive Standard"
	],
	"filament_flow_ratio": [
		"1.01"
	],
	"filament_flush_temp": [
		"0"
	],
	"filament_flush_volumetric_speed": [
		"0"
	],
	"filament_id": "P2bee256",
	"filament_ironing_flow": [
		"nil"
	],
	"filament_ironing_inset": [
		"nil"
	],
	"filament_ironing_spacing": [
		"nil"
	],
	"filament_ironing_speed": [
		"nil"
	],
	"filament_is_support": [
		"0"
	],
	"filament_loading_speed": [
		"28"
	],
	"filament_loading_speed_start": [
		"3"
	],
	"filament_long_retractions_when_cut": [
		"nil"
	],
	"filament_max_volumetric_speed": [
		"20"
	],
	"filament_minimal_purge_on_wipe_tower": [
		"15"
	],
	"filament_multitool_ramming": [
		"0"
	],
	"filament_multitool_ramming_flow": [
		"10"
	],
	"filament_multitool_ramming_volume": [
		"10"
	],
	"filament_notes": [
		""
	],
	"filament_printable": [
		"3"
	],
	"filament_ramming_parameters": [
		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
	],
	"filament_retract_before_wipe": [
		"nil"
	],
	"filament_retract_lift_above": [
		"nil"
	],
	"filament_retract_lift_below": [
		"nil"
	],
	"filament_retract_lift_enforce": [
		"nil"
	],
	"filament_retract_restart_extra": [
		"nil"
	],
	"filament_retract_when_changing_layer": [
		"nil"
	],
	"filament_retraction_distances_when_cut": [
		"nil"
	],
	"filament_retraction_length": [
		"nil"
	],
	"filament_retraction_minimum_travel": [
		"nil"
	],
	"filament_retraction_speed": [
		"nil"
	],
	"filament_settings_id": [
		"STAR PLAST PLA HS U1 @Snapmaker U1 (0.4 nozzle) - 1"
	],
	"filament_shrink": [
		"100%"
	],
	"filament_shrinkage_compensation_z": [
		"100%"
	],
	"filament_soluble": [
		"0"
	],
	"filament_stamping_distance": [
		"0"
	],
	"filament_stamping_loading_speed": [
		"0"
	],
	"filament_start_gcode": [
		"; Filament gcode\n"
	],
	"filament_toolchange_delay": [
		"0"
	],
	"filament_tower_interface_pre_extrusion_dist": [
		"10"
	],
	"filament_tower_interface_pre_extrusion_length": [
		"0"
	],
	"filament_tower_interface_print_temp": [
		"-1"
	],
	"filament_tower_interface_purge_volume": [
		"20"
	],
	"filament_tower_ironing_area": [
		"4"
	],
	"filament_type": [
		"PLA"
	],
	"filament_unloading_speed": [
		"90"
	],
	"filament_unloading_speed_start": [
		"100"
	],
	"filament_vendor": [
		"STAR PLAST"
	],
	"filament_wipe": [
		"nil"
	],
	"filament_wipe_distance": [
		"nil"
	],
	"filament_z_hop": [
		"nil"
	],
	"filament_z_hop_types": [
		"nil"
	],
	"first_x_layer_fan_speed": [
		"0"
	],
	"from": "User",
	"full_fan_speed_layer": [
		"2"
	],
	"hot_plate_temp": [
		"55"
	],
	"hot_plate_temp_initial_layer": [
		"55"
	],
	"idle_temperature": [
		"0"
	],
	"inherits": "",
	"internal_bridge_fan_speed": [
		"-1"
	],
	"ironing_fan_speed": [
		"-1"
	],
	"long_retractions_when_ec": [
		"0"
	],
	"name": "STAR PLAST PLA HS U1 @Snapmaker U1 (0.4 nozzle) - 1",
	"nozzle_temperature": [
		"220"
	],
	"nozzle_temperature_initial_layer": [
		"220"
	],
	"nozzle_temperature_range_high": [
		"240"
	],
	"nozzle_temperature_range_low": [
		"190"
	],
	"overhang_fan_speed": [
		"100"
	],
	"overhang_fan_threshold": [
		"50%"
	],
	"pellet_flow_coefficient": [
		"0.4157"
	],
	"pressure_advance": [
		"0.02"
	],
	"reduce_fan_stop_start_freq": [
		"1"
	],
	"required_nozzle_HRC": [
		"3"
	],
	"retraction_distances_when_ec": [
		"10"
	],
	"slow_down_for_layer_cooling": [
		"1"
	],
	"slow_down_layer_time": [
		"6"
	],
	"slow_down_min_speed": [
		"10"
	],
	"supertack_plate_temp": [
		"45"
	],
	"supertack_plate_temp_initial_layer": [
		"45"
	],
	"support_material_interface_fan_speed": [
		"-1"
	],
	"temperature_vitrification": [
		"45"
	],
	"textured_cool_plate_temp": [
		"40"
	],
	"textured_cool_plate_temp_initial_layer": [
		"40"
	],
	"textured_plate_temp": [
		"55"
	],
	"textured_plate_temp_initial_layer": [
		"55"
	],
	"version": "2.4.0.3",
	"volumetric_speed_coefficients": [
		""
	]
}